I need help with...

For larger holes, use a hole saw. It ranges in size from about 1" to 4" and has a pilot bit and a saw-toothed circular rim.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

A rip blade also has teeth bent to the left and right, but its teeth are on the top of the blade, not on the inside. They like chisels that scoop out the wood as the saw moves along the grain.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

For general use, you can, but a combination blade incorporates the features of both rip and crosscut blades.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

• Using a pencil, mark a cut on your piece of wood.

• Adjust the blade on your miter saw so that it lines up perfectly with your cut mark. (If you’re making square boxes or picture frames or if you’re cutting angles for crown molding, set your blade angle at precisely 45 degrees.)

• Turn on your blade and start your cut with a few backstrokes of the saw to give it a good channel for your cut.

• Make your cut with steady strokes by gently lowering the blade onto the wood.

• When the saw approaches the bottom of the board your cutting, ease back on the force you’re using so that the blade lightly passes through the wood. This will prevent the wood from ripping or tearing.

• Use a medium-grit sandpaper to sand the edges of your cut.

Check your state and local codes before starting any project. Follow all safety precautions. Every effort has been made to ensure the accuracy and safety of this information. Neither Westlake nor any contributor can be held responsible for damages or injuries resulting from the use of the information in this document.

That's common, but make sure you are using the right blade for the material you are cutting - wood, tile or metal.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

It is primarily used for cutting deep holes in all types of wood.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

The numbers indicate the number of points per inch on a saw blade.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

For drilling medium-sized holes in wood, a spade bit is a good choice. Common sizes range from 1/4 inch to 1-1/2 inch. They can also be used on chipboards and floorboards.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

The cutting edges are made from extra-hard carbide steel that will last up to 20 times longer, and it is good for cutting materials of different hardnesses.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

For drilling smaller holes in a variety of materials, choose a high-speed steel twist bit. These can drill holes from about 1/16 inch to 1/2 inch in wood, soft metal and other materials.

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.